用“pinion”造句大全，pinion造句
pinion-and-rack steering gear
bevel pinion and bevel gear set
Excessive distance between pinion gear and flywheel/drive plate gear.
Check ring gear and pinion gear teeth contact pattern.
Rotate case with Turning Bar C–4487–4 until the pinion mate shaft holes in pinion gears align with holes in casIt may be necessary to slightly tighten the forcing screw in order to install the pinion gears.
Drive pinion to stop collar clearance shall be controlled to OEM specifications.
Analysis about pinion gear bearing shim measuring influence factors & optimization in re-checking scheme
An over-running clutch on the drive pinion prevents the starter from being driven by the engine once it starts.
Rose leaves are dark green, but strangely, each leaf has soft spines on the edge, like a pinion.
Loss of air pressure, the stored energy in the springs forces the pistons inwards, the pinion turns clockwise while air is being exhausted from Port A.
As one of the individual variable vanes is rotated by an actuation source, the other variable vanes of the variable vane array are rotated a like amount by the rack and pinion gear interface.
"The planetary-gear system consists of an outer ring gear(sometimes called the internal gear because its teeth are inside), three planet pinions held on pinion shafts in a cage or carrier, and a sun gear."
rack and pinion gear
axle drive pinion adjusting sleeve
fine pitch automatic pinion shaft hobbing machine
Using a short piece of pipe and Holder 6958 to hold the pinion yoke, or pinion flange, remove the pinion nut and washer.
Usually, we adopt pinion drive for large mills.
"To permit this, the two pinion gears rotate on their pinion shaft, transmitting more turning movement to the outer side gear than to the inner side gear."
Rotate the pinion gear several complete revolutions to align the bearing rollers.
a wheel gear (the pinion) meshes with a toothed rack; converts rotary to reciprocating motion (and vice versa).
It has many advanced equipments, such as driving axle spiral bevel gears processing lines from Gleason Company and the ring gear &pinion producing machines from Mitsubishi Company.
Our typical applications includes: Furnace tilt drives and bull gear arrangements, Main ladle hoists and travel drives, Roller table drives, edger rolls, Rolling mill pinion stands and reducers, Drives for coilers, uncoilers, edgers, shears etc.
pinion-and-rack steering
drive pinion cone bearing cup
Install the pinion mate gears and thrust washers.
Attached to the ring gear (through the differential case) is a differential-pinion shaft on which are assembled two differential-pinion gears.
The trunnion sprocket has come off the pinion,but do not worry - we'll soon but that right.
The integral type housing, hypoid gear design has the centerline of the pinion set above the centerline of the ring gear.
hand rack pinion press
rack and pinion suspension system
"When the car is on a straight road, the two differential-pinion gears do not rotate on the pinion shaft."
Position the pinion yoke on the end of the shaft with the reference marks aligne
The ring gear is attached to the differential case so that the ease rotates with the ring gear when the latter is driven by the drive pinion.
rear axle differential spider pinion
The driving power enters the differential through the drive pinion on the end of the propeller shaft. The drive pinion is meshed with a large ring gear so that the ring gear revolves with the pinion.
The flywheel also has a large ring gear at its outer edge, which engages with a pinion gear on the starter motor during engine cranking.
rear axle bevel gear and pinion set
Align mark on front universal joint, or CV joint, to the mark on the axle pinion yoke, or flange.
twin-pinion single-output reduction gear
propeller shaft pinion flange
Remove the universal joint strap bolts at the pinion shaft yoke.
For increased accuracy and repeatability, the unit can be supplied with an external anti-backlash POM (polymer) pinion gear which optimizes coupling to the wind turbine's large yaw bull gear.
