用“bending”造句大全，bending造句

Processing projects: shearing, bending, stretch bending, roll bending, roll round, welding, drilling and tapping, customer sample processing services.

Except for the typical bending and torsion modes, the chord-wise bending modes have low frequencies.

Fabric by tester dull color. gives degrees operation and simple calculation out the fabric of bending height, bending rigidity, bending modulus. Standard: ERT 50-2 ASTM D1388 bs3356.

Sophia, bending over her books, made no answer.

Under the constant bending times, the biggest bending angle can be obtained with an optimal accumulative line energy value.

Curve flexibility may dictate the degree of the fulcrum bending correction index, whereby a curve that is less flexible may achieve a greater fulcrum bending correction index.

Several shape memory alloy(SMA) wires are embedded in liquid rubber at room temperature to form planar bending and spacial bending SMA actuators(SMAAs).

It is special equipment for insulating glass aluminum spacing frame rectangle bending.

Prince Ippolit brought her reticule, moved to her side, and bending close over her chair, sat beside her.

We has determined the bending strength of blockboard which has different core and different resin content, in order to study the factor which affects the bending strength of blockboard.

Don't always give yourself up to others, because few people in the world are worth bending over. Bending down for a long time will only make people accustomed to your low profile, your unimportant.

Followly, the bending rigidity and transverse shearing rigidity of one-way bamboo-stripe laminates applied to shipbuilding has been measured practically with this method.

Furthermore, the modification has no obvious influence on the hardness of high boron and low carbon ferroalloy, but increases its impact toughness and bending strength obviously.

Do not switch when starting pump: fill too tightly or between the impeller and pump body and the plug was stuck debris or shaft, bearings, minus leakage ring rust to live, or severe bending shaft.

The authors used the method of trigonometric series and polynomial to solve the problem for the bending of a cantilever plate in a symmetric triangular shape under uniform load.

pedal bending machine

I often sit with my back bending.

Periodic bending causes wave formation in fibers.

The bending technology of the thick-wall supprt of aluminum alloy was analyzed, and the flattening length of bending, blanking force, piercing force and bending force were calculated.

Test method for bending of rigid cellular plastics

Result shows that permanent bending and thermal bending after excitation are the main reasons leaded to the high vibration amplitude of the generator.

APEX is that the so-called cornering lines closest to the center of that point bending.

I am talking about walking around, swinging your arms, kicking your feet, bending, and twisting.

At the same time, the spring back allowance of bottoming bending of circle section rod is analyzed.

Its test results are different between tension and bending test methods, as well as between small-specimen and large panel.

The large deflections and stiffness changes usually associated with plastic bending can significantly change the internal load distribution, particularly in statically indeterminate beams.

根据今年四月的一项脑子抽抽（mind-bending）的研究觉得，黑洞是联通两个宇宙间的隧道——类似虫子孔。

Compression knee bands discourage bending.

He was bending over the desk, drawing.

During the bending processing, the bending buffer distance piece (42) can easily realize the bending and greatly ensures the performance of the core unit.

The effects of bending support span, solder pad size, reflow and aging history on PCB bending reliability are discussed.

Reliability sensitivity of jib with bending and torsion stiffness failure modes was proposed.

Abstract: Abstract: CNC Frame Bending Machine is mainly used for bending, straightening of ship frame, and also it is a smart equipment for frame edge cutting and pneumatic printing.

The calculation of ledger maximum bending moment and deformation the even load of scaffold board and live loads above the ledger.

Where condition (4) above is not fulfilled, the effective depth of the steel for the calculation of bending resistance in accordance with 6.1 should apply to the layer furthest from the tension face.

four-roll plate bending machine

The last set is also bending die casting die for bending two sides.

Experimentation data shows that the principle of bending mechanism in this article is feasible, finite element model of bending mechanism is credible and its design method is dependable.

Flexion is soft, stretching is rigid, bending is the accumulation of energy, extension is the release after accumulation, and bending is a kind of tolerance, and it is also a kind of courage.

The effect of imposing natural boundary condition as constraints is considered and it is shown by a plate bending problem that this effect is quite superficial.

four-roll bending machine

C an you touch your toes without bending your knees?

Do not allow the tube to slip inside the bender while the bending is in progress.

Qu bending and drainage flow, separated by Jing Jing, small and, to the natural landscape in the courtyard between the microfilm, is a typical feature of the Oriental garden;

Bending knows bending, in order not to break integrity. Sometimes, proper bending is a kind of reason. In reality, bending contains rich philosophy.

But the people devouring mind-bending substances in Cambridge are a middle-class bunch, and some are downright posh.

I have had some experience of bending on hole 3. How to control the half bending and full bending?

A Pinus sylvestris pillar, have bending tilt, let alone 26 pieces of broken bone piece together into a spine?

This article reviews the theory of rotary draw bending, basic tools required and their functions as well as operating sequences of bending.

bending stiffness

Suppose time is a circle, bending back on itself.